AircraftMotion

From SIMboxWiki
Jump to navigation Jump to search

[[#top|]] The old flight model for the aircrafts.

Type: Logic Object Component
File: AircraftMotion.slc
Version: 450.1000.355.1


back to top

Icon properties.png Properties

Name Description MaxValue MinValue DisplayName UnitType UnitName
PROP_AGL_HEIGHT  Object AGL Height.  AGL Height  Default  Default 
PROP_ATK_FILE_NAME  ATK file name. Relative to resource directory.  Aero Tool Kit file name (no suffix required)  File System  File 
PROP_AUTO_THROTTLE_GAIN  Gain of the Auto Throttle AP  1000  -1000    Default  Default 
PROP_AUTO_TRIMMING_MAX_BANK_ANGLE_DEG  The maximum bank angle to operate auto trimmer  90    Default  Default 
PROP_AUTO_TRIMMING_TO_BANK_ANGLE_FACTOR  The bank angle contribution to the auto trimming mechanism  10    Default  Default 
PROP_AUTO_TRIMMING_TO_BANK_ANGLE_FACTOR_FLAPS  The bank angle contribution to the auto trimming mechanism while flying with open flaps  10    Default  Default 
PROP_AUTO_TRIMMING_TO_BANK_ANGLE_FACTOR_LANDING_GEAR  The bank angle contribution to the auto trimming mechanism while flying with open landing gears  10    Default  Default 
PROP_AUTOCOORDINATION_ON  Set Autocoordination to ON    Default  Default 
PROP_AUTOPILOT_HOLD_TRACK_GAIN  The AutoPilot Hold Track Gain  10    Default  Default 
PROP_AUTOPILOT_MAX_BANK_ANGLE_DEG  The AutoPilot Max Bank Angle  180    Default  Default 
PROP_BANK_LIMITER_ACTIVE  is Bank limiter active (0 - not active, 1 - active)    Default  Default 
PROP_BANK_LIMITER_MAX_ANGLE_DEG  maximum bank Limiter angle  180    Default  Default 
PROP_CAT3_LATERAL_GAINS_PERCENTAGE  Percentage of control gain of CAT3 respective to CAT1 in Lateral plane[0..100]  100    Default  Default 
PROP_CAT3_LONGITUDAL_GAINS_PERCENTAGE  Percentage of control gain of CAT3 respective to CAT1 in Longitudal plane[0..100]  100    Default  Default 
PROP_CHASE_CAMERA_TYPE_NAME  name of chase camera type (ORI,SPEED)    Default  Default 
PROP_CONTROL_DEAD_ZONE  Aircraft control dead zone [%]  100    Default  Default 
PROP_CONTROLLED_INTEGRATION_CYCLE_STEP_LIMIT  The integration cycle step for controlled aircraft  0.01    Default  Default 
PROP_DEBRIEF_TRAIL_NAME  name of the trail for wing-tip effect    Default  Default 
PROP_DEFAULT_ATK_FILE_NAME  Default ATK file name. Relative to resource directory.    File System  File 
PROP_ENGINE_STATUS_ON_GROUND  OFF | IDL : OFF - Engine not started, IDL - Engine started and in IDL    Default  Default 
PROP_FLY_BY_WIRE_AOA_POWER  The influence of angle of attack change on roll rate   90    Default  Default 
PROP_FLY_BY_WIRE_MAX_AOA_TO_MAX_ROLL_RATE  The maximum angle of attack whick is not affected by the roll rate control loop of fly by wire aircraft  90    Default  Default 
PROP_FLY_BY_WIRE_MIN_ROLL_RATE_DUMP_PERCENTAGE  The minimum roll rate dump percentage on maximum angle of attack  100    Default  Default 
PROP_GEAR_SOUND_FILE_NAME  Gears sound file.    File System  File 
PROP_HEADING  Object heading  360  Heading  Default  Default 
PROP_INITIAL_FUEL_WEIGHT  initial fuel weight [lb]  100000  Fuel Quantity  Default  Default 
PROP_INITIAL_LANDING_GEARS_STATE  RETRACTED - Gears are folded, EXTRACTED - Gears are down  Landing Gear State  Default  Default 
PROP_INITIAL_PARKING_BRAKES_STATE  True - Parking brakes engaged, False - Parking brakes disengaged  Parking Brakes  Default  Default 
PROP_INITIAL_TRUE_AIR_SPEED  Aircraft initial true velocity in knots  500  TAS (kts)  Default  Default 
PROP_IS_AB_EXIST  Is After burner available    Default  Default 
PROP_IS_AGL  Indicates if PROP_AGL_HEIGHT should be used.  Use AGL height  Default  Default 
PROP_IS_TO_HANDLE_LANIDNG_GEARS  is to handle landing gears up/down    Default  Default 
PROP_JET_ENGINE_RPM_PERCENTAGE_AB  The Jet Engine RPM percentage on After Burner  103  Jet Engine RPM - Afterburner  Default  Default 
PROP_JET_ENGINE_RPM_PERCENTAGE_IDLE  The Jet Engine RPM percentage on Idle  103  Jet Engine RPM - Idle  Default  Default 
PROP_JET_ENGINE_RPM_PERCENTAGE_MIL  The Jet Engine RPM percentage on Military  103  Jet Engine RPM - MIL  Default  Default 
PROP_LANDING_LATERAL_GAINS_PERCENTAGE  Percentage of control gain for Landing respective to CAT1 in Lateral plane[0..100]  100    Default  Default 
PROP_LANDING_LONGITUDAL_GAINS_PERCENTAGE  Percentage of control gain for Landing respective to CAT1 in Longitudal plane[0..100]  100    Default  Default 
PROP_LATITUDE  Object Latitude  Latitude  Default  Default 
PROP_LOADOUT_EFFECT_ACTIVE  True - Take into account the loadout for computing aerodynamics    Default  Default 
PROP_LONGITUDE  Object Longitude  Longitude  Default  Default 
PROP_LOWER_FLAPS_WITH_GEARS  True - Lower the Flaps when lowering the Gears    Default  Default 
PROP_PITCH_INIT  Aircraft start pitch  90  -90  Pitch  Default  Default 
PROP_ROLL_CMD_INNER_RANGE_CMD  Roll command inner range aircraft roll command definition. Set negative to ignore    Default  Default 
PROP_ROLL_CMD_INNER_RANGE_STICK  Roll command inner range stick movement definition. Set negative to ignore    Default  Default 
PROP_ROLL_CMD_NULL_ZONE  Roll command null zone. Set negative to ignore    Default  Default 
PROP_ROLL_INIT  Aircraft start roll  180  -180  Roll  Default  Default 
PROP_ROLL_TRIM_GAIN  100 - max , 0 - min    Default  Default 
PROP_THROTTLE_POS  initial throttle position [%] (40 - IDL : 77 - MIL : 100 - AB)  120  Throttle Initiate Position (in engine percents)  Default  Default 
PROP_UNCONTROLLED_INTEGRATION_CYCLE_STEP_LIMIT  The integration cycle step for uncontrolled aircraft  0.01    Default  Default 
PROP_WING_TIP_TRAIL_NAME  name of the trail for wing-tip effect    Default  Default 
PROP_XPOSITION  Object X Position    Default  Default 
PROP_YPOSITION  Object Y Position    Default  Default 
PROP_ZPOSITION  Object Z Position  Altitude  Default  Default 

back to top

Icon attributes.png Attributes

Name Description Param1 Param2 DisplayName UnitType UnitName
ATT_ABS_VELOCITY  Entity Absolute Velocity  float &      Speed  Meter Per Second 
ATT_ACTUAL_G  returns the load factor acting on the aircraft (G) [N/A]  float &    G (Current)  Acceleration 
ATT_AFTERBURNER_STATUS  Indicates the afterburner status so the external can activate the afterburner effect accordingly  int &      Default  Default 
ATT_AILERON_TRIM_ANGLE_RAD  returns the aileron current trim angle [rad]  float &      Angle  Radian 
ATT_AILERONS_HIGH_RAD  returns the aircraft max aileron extraction downwards [rad]  float &      Default  Default 
ATT_AILERONS_LOW_RAD  returns the aircraft max aileron extraction upwards [rad]  float &      Default  Default 
ATT_AIRCRAFT_FUEL_QUANTITY  returns the aircraft fuel Quantity [kg]  float &    Fuel Quantity  Mass  KG 
ATT_AIRCRAFT_FUEL_QUANTITY_LBS  returns the aircraft fuel Quantity [LBS]  float &      Mass  LB 
ATT_AIRCRAFT_WEIGHT  returns the aircraft weight [lb]  float &    Aircraft Weight  Mass  LB 
ATT_AIRCRAFT_WEIGHT_EMPTY  returns the aircraft empty weight[lb]  float &      Mass  LB 
ATT_AIRCRAFT_WEIGHT_LOADOUT  returns the aircraft weight with loadout[lb]  float &      Mass  LB 
ATT_ANG_ACCELERATION  Entity angular Acceleration vector  AngularVec &      Default  Default 
ATT_ANG_VELOCITY  Entity angular Velocity vector  AngularVec &      Default  Default 
ATT_ANGLE_OF_ATTACK_RAD  returns the aircraft angle of attack [rad]  float &      Angle  Radian 
ATT_ARE_AIR_BRAKES_OPEN  returns if aircraft air brakes are open  bool &    Speed brakes are Extracted?  Default  Default 
ATT_ARE_FLAPS_OPEN  returns if aircraft flaps are open  bool &    Flaps are Extracted / Lowered?  Default  Default 
ATT_ARE_LANDING_GEARS_OPEN  returns if the aircraft landing gears are open  bool &    Landing Gear are Extended?  Default  Default 
ATT_ARE_PARKING_BRAKES_OPEN  returns if aircraft parking brakes are open  bool &    Parking Brakes are Extended?  Default  Default 
ATT_ARE_WHEEL_BRAKES_OPEN  returns if aircraft wheel brakes are open  bool &      Default  Default 
ATT_AUTO_PILOT_LATERAL_ON  get is autopilot active in lateral axes  bool &      Default  Default 
ATT_AUTO_PILOT_LONGTITUDAL_ON  get is autopilot active in longtitudal axes  bool &      Default  Default 
ATT_AUTO_PILOT_PANEL_AIRSPEED_VALUE  get airspeed number  float &      Speed  Meter Per Second 
ATT_AUTO_PILOT_PANEL_ALTITUDE_VALUE  get altitude lock var number  float &      Length  Meter 
ATT_AUTO_PILOT_PANEL_HEADING_VALUE_DEG  get Auto pilot Panel heading lock director [deg]  float &      Angle  Degree 
ATT_AUTO_PILOT_PANEL_IS_AIRSPEED_HOLD  return true if airspeed control active  bool &      Default  Default 
ATT_AUTO_PILOT_PANEL_IS_ALTITUDE_HOLD  return true if altitude control active  bool &      Default  Default 
ATT_AUTO_PILOT_PANEL_IS_HEADING_HOLD  return true if heading control active  bool &      Default  Default 
ATT_AUTO_PILOT_PANEL_IS_MACH_HOLD  return true if hold mach control loop active  bool &      Default  Default 
ATT_AUTO_PILOT_PANEL_IS_VERTICAL_SPEED_HOLD  return true if vertical speed control loop active  bool &      Default  Default 
ATT_AUTO_PILOT_PANEL_MACH_VALUE  get the requested mach numbe  float &      Default  Default 
ATT_AUTO_PILOT_PANEL_ROLL_VALUE_DEG  get roll lock var number  float &      Angle  Degree 
ATT_AUTO_PILOT_PANEL_TRACK_VALUE_DEG  get the requested Auto pilot Panel track [deg]  float &      Angle  Degree 
ATT_AUTO_PILOT_PANEL_VERTICAL_SPEED_VALUE_M2SEC  get vertical speed value  float &      Speed  Meter Per Second 
ATT_AUTO_PILOT_THROTTLE_ON  get is autopilot active in throttle axes  bool &      Default  Default 
ATT_AVERAGE_ENGINE_RPM  get average rpm  float &      Angular Velocity  RPM 
ATT_AVERAGE_THROTTLE_LEVER_POS  get average throttle lever pos  float &      Default  Default 
ATT_CABIN_PRESS_ALT  The cabbin pressure altitde [ft]  float &      Length  Feet 
ATT_CHASE_CAMERA_TYPE  returns the chase camera type (ORI,SPEED)  string &      Default  Default 
ATT_CURRENT_CONTROL_GAINS_TYPE  Aircraft current Control Gains (CAT1/CAT3/LANDING)  string &      Default  Default 
ATT_DEBUG_PARAM  debug  const int  float &    Default  Default 
ATT_DISTANCE_FROM_RADIAL  Distance From Radial  float &      Default  Default 
ATT_ELEVATOR_HIGH_RAD  returns the aircraft max elevator extraction downwards [rad]  float &      Default  Default 
ATT_ELEVATOR_LOW_RAD  returns the aircraft max elevator extraction upwards [rad]  float &      Default  Default 
ATT_ELEVATOR_TRIM_ANGLE_RAD  returns the elevator current trim angle [rad]  float &      Angle  Radian 
ATT_ENGINE_CHARGING_AMPS    const int  float &    Default  Default 
ATT_ENGINE_COMBINED_AB1_PERCENT  return above 75 if ab, below on regular engine  float &      Default  Default 
ATT_ENGINE_COMBINED_AB2_PERCENT  return above 75 if ab, below on regular engine  float &      Default  Default 
ATT_ENGINE_CYLINDER_HEAD_TEMP    const int  float &    Temperature  Celsius 
ATT_ENGINE_EXHAUST_GAS_TEMP    const int  float &    Temperature  Celsius 
ATT_ENGINE_FUEL_FLOW  returns the engines Fuel Flow [Kg/sec]  float &      Mass Flow  KG Per Second 
ATT_ENGINE_FUEL_FLOW_GPH    const int  float &    Default  Default 
ATT_ENGINE_FUEL_FLOW_PPH    const int  float &    Default  Default 
ATT_ENGINE_FUEL_FLOW_SSL    const int  float &    Default  Default 
ATT_ENGINE_FUEL_PRESSURE    const int  float &    Default  Default 
ATT_ENGINE_HYDRAULIC_PRESSURE    const int  float &    Default  Default 
ATT_ENGINE_HYDRAULIC_QUANTITY    const int  float &    Default  Default 
ATT_ENGINE_IS_ON_FIRE  returns true if engine is on fire  const int  bool &    Default  Default 
ATT_ENGINE_IS_WORKING  returns true if engine is on fire  const int  bool &  Engine is working  Default  Default 
ATT_ENGINE_MAGNETO_LEFT_STATE  Returns left magneto position. 1 - on  const int  float &  Engine Magneto Left State  Default  Default 
ATT_ENGINE_MAGNETO_RIGHT_STATE  Returns right magneto position. 1 - on  const int  float &  Engine Magneto Right State  Default  Default 
ATT_ENGINE_MANIFOLD_PRESSURE_PERC    const int  float &    Default  Default 
ATT_ENGINE_MAX_CHT  returns the aircraft engines max cylinder head temprature [Deg F]  float &      Temperature  Fahrenheit 
ATT_ENGINE_MAX_EGT  returns the aircraft engines max exhuast gas temprature [Deg F]  float &      Temperature  Fahrenheit 
ATT_ENGINE_MAX_FUELFLOW  returns the aircraft engines max fuel flow [PPH]  float &      Mass Flow  LB Per Hour 
ATT_ENGINE_MAX_HYDRAULIC_PRESSURE  returns the aircraft engines max hydraulic pressure [psi]  float &      Pressure  PSI 
ATT_ENGINE_MAX_MANIFOLD_PRESSURE  returns the aircraft engines max manifold pressure [inHg]  float &    Manifold Pressure (Max)  Pressure  InHG 
ATT_ENGINE_MAX_OIL_PRESSURE  returns the aircraft engines max oil pressure [psi]  float &    Engine Oil Pressure (Max)  Pressure  PSI 
ATT_ENGINE_MAX_OIL_QUANTITY  returns the aircraft engines max oil quantity [Galons]  float &    Engine Oil Quant (Max)  Mass  Metric Ton 
ATT_ENGINE_MAX_OIL_TEMPRATURE  returns the aircraft engines max oil temprature [Deg F]  float &    Engine Oil Temp (Max)  Temperature  Fahrenheit 
ATT_ENGINE_MAX_POWER  returns the aircraft engines max power [Hp]  float &    Engine Oil Power (Max)  Power  HP 
ATT_ENGINE_MAX_RPM  returns the aircraft engines max rpm [RPM]  float &    Engine Oil RPM (Max)  Angular Velocity  RPM 
ATT_ENGINE_MAX_TIT  returns the aircraft engines max turbine inlet temprature [Deg F]  float &      Temperature  Fahrenheit 
ATT_ENGINE_MIN_CHT  returns the aircraft engines min cylinder head temprature [Deg F]  float &      Temperature  Fahrenheit 
ATT_ENGINE_MIN_EGT  returns the aircraft engines min exhuast gas temprature [Deg F]  float &      Temperature  Fahrenheit 
ATT_ENGINE_MIN_FUELFLOW  returns the aircraft engines min fuel flow [PPH]  float &      Mass Flow  LB Per Hour 
ATT_ENGINE_MIN_HYDRAULIC_PRESSURE  returns the aircraft engines min hydraulic pressure [psi]  float &      Pressure  PSI 
ATT_ENGINE_MIN_MANIFOLD_PRESSURE  returns the aircraft engines min manifold pressure [inHg]  float &      Pressure  InHG 
ATT_ENGINE_MIN_OIL_PRESSURE  returns the aircraft engines min oil pressure [psi]  float &      Pressure  PSI 
ATT_ENGINE_MIN_OIL_QUANTITY  returns the aircraft engines min oil quantity [Galons]  float &      Mass  Metric Ton 
ATT_ENGINE_MIN_OIL_TEMPRATURE  returns the aircraft engines min oil temprature [Deg F]  float &      Temperature  Fahrenheit 
ATT_ENGINE_MIN_TIT  returns the aircraft engines min turbine inlet temprature [Deg F]  float &      Temperature  Fahrenheit 
ATT_ENGINE_MIXTURE_LEVER_COM  Returns the input command for the mixture lever position. between 0 - 1  const int  float &    Default  Default 
ATT_ENGINE_MIXTURE_LEVER_POS  Returns the actual propeller mixture position. between 0 - 1  const int  float &  Engine Mixture Lever Position  Default  Default 
ATT_ENGINE_N1_RPM    const int  float &    Angular Velocity  RPM 
ATT_ENGINE_N2_RPM    const int  float &    Angular Velocity  RPM 
ATT_ENGINE_OIL_PRESSURE    const int  float &    Default  Default 
ATT_ENGINE_OIL_QUANTITY    const int  float &    Default  Default 
ATT_ENGINE_OIL_TEMPRATURE    const int  float &    Default  Default 
ATT_ENGINE_POWER  returns the engine power[N*m/t]  const int  float &    Default  Default 
ATT_ENGINE_POWER_HP    const int  float &    Power  HP 
ATT_ENGINE_PRESS_RATIO    const int  float &    Default  Default 
ATT_ENGINE_PRESSURE_BUG_POS    const int  float &    Default  Default 
ATT_ENGINE_PROP_LEVER_POSITION    const int  float &    Default  Default 
ATT_ENGINE_PROPELLER_LEVER_COM  Returns the input command for the propeller lever position. between 0 - 1  const int  float &    Default  Default 
ATT_ENGINE_PROPELLER_LEVER_POS  Returns the actual propeller lever position. between 0 - 1  const int  float &  Engine Propeller Lever Position  Default  Default 
ATT_ENGINE_ROTOR_RPM    const int  float &    Angular Velocity  RPM 
ATT_ENGINE_ROTOR_RPM_SCALER    const int  float &    Default  Default 
ATT_ENGINE_RPM  returns the engine rpm[Rpm]  const int  float &  Engine RPM  Angular Velocity  RPM 
ATT_ENGINE_STARTER_STATE  Returns the starter position. 4 - is on  const int  float &  Engine Starter Position  Default  Default 
ATT_ENGINE_THROTTLE_LEVER_COM    const int  float &    Default  Default 
ATT_ENGINE_THROTTLE_LEVER_POS    const int  float &  Engine Throttle Lever Position  Default  Default 
ATT_ENGINE_TORQUE    const int  float &    Default  Default 
ATT_ENGINE_TORQUE_PERCENT    const int  float &    Default  Default 
ATT_ENGINE_TRANSMISSION_PRESSURE    const int  float &    Default  Default 
ATT_ENGINE_TRANSMISSION_TEMPRATURE    const int  float &    Temperature  Celsius 
ATT_ENGINE_TURBINE_INLET_TEMP    const int  float &    Temperature  Celsius 
ATT_ENGINE_VIBRATIONS    const int  float &    Default  Default 
ATT_FCC_AUTO_COORDINATION_STATUS  returns the auto coordination system status (0 - not active, 1 - active)  int &      Default  Default 
ATT_FCC_BANK_LIMITER_STATUS  returns the stability augmentation system status (0 - not active, 1 - active)  int &      Default  Default 
ATT_FCC_SAS_STATUS  int,returns the stability augmentation system status (0 - not active, 1 - active)  int &      Default  Default 
ATT_FCC_TRIMMER_STATUS  returns the stability trimmers system status (0 - not active, 1 - Auto trimmer active, 2 - Manuel trimmer active)  int &      Default  Default 
ATT_FCC_YAW_DAMPER_STATUS  returns the yaw damp system status (0 - not active, 1 - active)  int &      Default  Default 
ATT_FLAPS_CURRENT_STAGE  returns the flaps current stage  int &    Flaps Stage  Default  Default 
ATT_FLAPS_LIMIT_DEG  returns the aircraft flaps extraction limit [deg]  float &      Default  Default 
ATT_FLIGHT_DIRECTOR_GLIDE_SLOPE_STATE  get glide slope state  int &      Default  Default 
ATT_FLIGHT_DIRECTOR_IAS_MACH_SWITCH  false - HOLD_IAS / true - HOLD_MACH   bool &      Default  Default 
ATT_FLIGHT_DIRECTOR_IS_ACTIVE  return true if flight director active  bool &      Default  Default 
ATT_FLIGHT_DIRECTOR_LOCALIZER_STATE  get glide localizer state  int &      Default  Default 
ATT_FLIGHT_DIRECTOR_PITCH  get flight director Pitch number  float &      Default  Default 
ATT_FLIGHT_DIRECTOR_ROLL  get flight director roll number  float &      Default  Default 
ATT_FLIGHT_MODEL_EXISTS  To Indicate that a flight model exists  bool &      Default  Default 
ATT_FPM_LOCATION  returns the 6DOF of the aircraft velocity vector[N/A]  Location &      Default  Default 
ATT_FUEL_FLOW_SCALAR  returns the height above ground [m]   float &      Volume Flow  Gallon Per Hour 
ATT_FUEL_WEIGHT  returns the aircraft fuel weight [kg]  float &    Fuel Weight  Mass  KG 
ATT_GEARS_LIMIT_RAD  returns the aircraft gears extraction limit [rad]  float &      Default  Default 
ATT_GROUND_VELOCITY  returns the aircraft ground velocity [m/s]  float &      Speed  Meter Per Second 
ATT_HEADING_TRUE  returns true heading [deg]  float &    Heading (True)  Angle  Degree 
ATT_HEIGHT  Entity height [m]  float &    Height (Meters)  Length  Meter 
ATT_HEIGHT_ABOVE_GROUND  returns the height above ground [m]   float &    AGL (Feet)  Length  Meter 
ATT_HEIGHT_ABOVE_GROUND_FEET  return height above ground [ft]  float &      Length  Feet 
ATT_HEIGHT_FEET  return height [ft]  float &      Length  Feet 
ATT_INDICATED_AIRSPEED  returns the aircraft indicated AirSpeed [m/s]  float &    IAS (m/s)  Speed  Meter Per Second 
ATT_INDICATED_AIRSPEED_KNOTS  returns the aircraft indicated AirSpeed [knots]  float &    IAS (knots)  Speed  Knots 
ATT_IS_AFTERBURNER_OPEN  returns if aircraft afterburner is open  const int  bool &  Afterburner (Engine 1) ON  Default  Default 
ATT_IS_AFTERBURNER2_OPEN  returns if aircraft afterburner2 is open  const int  bool &  Afterburner (Engine 2) ON  Default  Default 
ATT_IS_AUTOPILOT_ACTIVE  return true if autopilot control active  bool &    Is AP on?  Default  Default 
ATT_IS_FLAPERON  are the flaps part of the aileron mechanism  bool &      Default  Default 
ATT_IS_IN_MOTION  returns if the entity is in motion  bool &    Is entity in motion?  Default  Default 
ATT_IS_LANDING_GEARS_HANDLE_UP  returns True the aircraft landing gears handle is Up  bool &    Is Landing Gear handle in UP position?  Default  Default 
ATT_IS_LANDING_LIGHT_ON  Is landing light on  bool &    Landing Light ON?  Default  Default 
ATT_IS_MOTION_MODEL_UNIT  Is this SLC a part of the object's motion model  bool &      Default  Default 
ATT_IS_ON_GROUND  returns if aircraft is on ground  bool &    Is entity on the ground?  Default  Default 
ATT_IS_STALL_WARN  returns true if there should be a stall warn  bool &    Is the Stall Warning on?  Default  Default 
ATT_IS_TAXI_LIGHT_ON  Is landing light on  bool &    Is Taxi light on?  Default  Default 
ATT_IS_WINGTIPS_SMOGE  returns the aircraft wing tips state  bool &      Default  Default 
ATT_LATITUDE  Entity Latitude [rad]  double &      Angle  Radian 
ATT_LIN_ACCELERATION  Entity linear Acceleration vector  LinearVec &      Acceleration  Meter Per Second Squared 
ATT_LIN_VELOCITY  Entity Linear Velocity Vector (Vx,Vy,Vz)  LinearVec &      Speed  Meter Per Second 
ATT_LOCATION  Entity 6-DOF(Vx,Vy,Vz,pitch,roll,yaw)  Location &      Coordinate System  Local 
ATT_LONGITUDE  Entity Longitude [rad]  double &      Angle  Radian 
ATT_MACH  returns the aircraft mach number [N/A]  float &    Aicraft Mach number  Default  Default 
ATT_MAX_G  returns the max aircraft load factor(G) upper limit [N/A]  float &    Aircraft Maximum G limit  Default  Default 
ATT_MAX_ROLL_RATE  returns the aircraft max roll rate [rad/s]  float &      Default  Default 
ATT_MIN_G  returns the min aircraft load factor(G) lower limit [N/A]  float &      Default  Default 
ATT_NUMBER_OF_ENGINES  returns the number of engines of the aircraft  int &      Default  Default 
ATT_NUMBER_OF_FLAPS_STAGES  returns the number of flaps stages  int &      Default  Default 
ATT_ORIENTATION  Entity orientation (pitch,roll,yaw)  AngularVec &      Default  Default 
ATT_OUTSIDE_AIR_TEMPERATURE  The outside air temperature [oC]  float &      Temperature  Celsius 
ATT_PITCH_ANGLE_DEG  returns the aircraft pitch angle [deg]  float &    Aircraft Pitch  Angle  Degree 
ATT_POSITION  Entity position (x,y,z)  LinearVec &      Coordinate System  Local 
ATT_ROLL_ANGLE_DEG  returns the aircraft roll angle [deg]  float &    AIrcraft Roll  Angle  Degree 
ATT_RUDDER_LIMIT_RAD  returns the aircraft rudder extraction limit [rad]  float &      Default  Default 
ATT_RUDDER_TRIM_ANGLE_RAD  returns the rudder current trim angle [rad]  float &      Angle  Radian 
ATT_SIDESLIP_ANGLE_RAD  returns the aircraft side slip angle [rad]  float &      Angle  Radian 
ATT_SMOOTHED_ENGINE_POWER  returns the aircraft smoothed engine power [N/A]  const int  float &    Default  Default 
ATT_SPOILER_LIMIT_RAD  returns the aircraft spoiler extraction limit [rad]  float &      Default  Default 
ATT_SUBPART_ANG_AIRBRAKE  get subpart angular value (positive Y axis) [rad]  float &      Angle  Radian 
ATT_SUBPART_ANG_BAY_DOORS  get subpart angular value (positive Y axis) [rad]  float &      Angle  Radian 
ATT_SUBPART_ANG_FLAPS  get subpart angular value (positive Y axis) [rad]  float &      Angle  Radian 
ATT_SUBPART_ANG_FWD_GEAR  get subpart angular value (positive Y axis) [rad]  float &      Angle  Radian 
ATT_SUBPART_ANG_FWD_GEAR_DOORS  get subpart angular value (positive Y axis) [rad]  float &      Angle  Radian 
ATT_SUBPART_ANG_FWD_GEAR_DOORS_2  get subpart angular value (positive Y axis) [rad]  float &      Angle  Radian 
ATT_SUBPART_ANG_FWD_WHEEL  get subpart angular value (positive Y axis) [rad]  float &      Angle  Radian 
ATT_SUBPART_ANG_GEAR_DOORS  get subpart angular value (positive Y axis) [rad]  float &      Angle  Radian 
ATT_SUBPART_ANG_GEAR_DOORS_2  get subpart angular value (positive Y axis) [rad]  float &      Angle  Radian 
ATT_SUBPART_ANG_HATCH_DOORS  get subpart angular value (positive Y axis) [rad]  float &      Angle  Radian 
ATT_SUBPART_ANG_LEFT_AILRON  get subpart angular value (positive Y axis) [rad]  float &      Angle  Radian 
ATT_SUBPART_ANG_LEFT_ELEVATORS  get subpart angular value (positive Y axis) [rad]  float &      Angle  Radian 
ATT_SUBPART_ANG_LEFT_RUDDER  get subpart angular value (positive Y axis) [rad]  float &      Angle  Radian 
ATT_SUBPART_ANG_LFT_GEAR  get subpart angular value (positive Y axis) [rad]  float &      Angle  Radian 
ATT_SUBPART_ANG_LFT_WHEEL  get subpart angular value (positive Y axis) [rad]  float &      Angle  Radian 
ATT_SUBPART_ANG_RER_GEAR  get subpart angular value (positive Y axis) [rad]  float &      Angle  Radian 
ATT_SUBPART_ANG_RGT_GEAR  get subpart angular value (positive Y axis) [rad]  float &      Angle  Radian 
ATT_SUBPART_ANG_RGT_WHEEL  get subpart angular value (positive Y axis) [rad]  float &      Angle  Radian 
ATT_SUBPART_ANG_RIGHT_AILRON  get subpart angular value (positive Y axis) [rad]  float &      Angle  Radian 
ATT_SUBPART_ANG_RIGHT_ELEVATORS  get subpart angular value (positive Y axis) [rad]  float &      Angle  Radian 
ATT_SUBPART_ANG_RIGHT_RUDDER  get subpart angular value (positive Y axis) [rad]  float &      Angle  Radian 
ATT_SUBPART_ANG_SPOILER  get subpart angular value (positive Y axis) [rad]  float &      Angle  Radian 
ATT_SUBPART_ANG_STEERING_WHEEL  get subpart angular value (positive Y axis) [rad]  float &      Angle  Radian 
ATT_SUBPART_FLAPS_STAGE_ANGLE_DEG  returns The flaps stage Angle [deg]  const int  float &    Angle  Degree 
ATT_SUBPART_FLAPS_STAGE_SPEED_LIMIT  returns The flaps stage speed limit [m/sec]  const int  float &    Speed  Meter Per Second 
ATT_SUBPART_GEARS_ARE_FULL_EXTENDED  returns if aircraft landing gears are fully extended  bool &      Default  Default 
ATT_SUBPART_GEARS_ARE_RETRACTABLE  returns if aircraft landing gears are retractable  bool &      Default  Default 
ATT_SUBPART_VISIBLE_PARACHUTE  get subpart visible status (PARACH_CLOSED==0 || PARACH_BAD==1 || PARACH_OPEN==2 || PARACH_THROWN==3)   int &      Default  Default 
ATT_SUBPART_VISIBLE_PIPE  get subpart visible status (PIPE_A==0 || PIPE_B==1 || ...)   int &      Default  Default 
ATT_TERRAIN_HEIGHT  returns ground Height [m]   float &      Length  Meter 
ATT_THROTTLE_PERCENT  returns the throttle lever percent(0-1) [N/A]  const int  float &    Default  Default 
ATT_TRACK  returns current track [deg]  float &      Angle  Degree 
ATT_TRUE_AIR_SPEED_KNOTS  return entity velocity - TAS [knots]  float &      Speed  Knots 
ATT_TRUE_AIRSPEED  returns the aircraft true AirSpeed [m/s]  float &      Speed  Meter Per Second 
ATT_TURN_RATE  The aircraft turn rate [deg / sec]  float &      Angular Velocity  Degree Per Second 
ATT_VERTICAL_VELOCITY  returns the aircraft vertical velocity [m/s]  float &      Speed  Meter Per Second 
ATT_YAW_ANGLE_DEG  returns the aircraft yaw angle [deg]  float &      Angle  Degree 

back to top

Icon actions.png Actions

Name Description Param1 Param2 DisplayName UnitType UnitName
ACTION_ACTIVATE_AUTO_TRIMMER  active the Auto Trimmer        Default  Default 
ACTION_ACTIVATE_EXTINGUISHER  activate the engine extinguisher  const int      Default  Default 
ACTION_ACTIVATE_MANUAL_TRIMMER  active the Manual Trimmer        Default  Default 
ACTION_AP_AIRSPEED_HOLD_OFF  Speed Hold Off        Default  Default 
ACTION_AP_AIRSPEED_HOLD_ON  Speed Hold On        Default  Default 
ACTION_AP_AIRSPEED_VAR_DEC  decrease the airspeed var value        Default  Default 
ACTION_AP_AIRSPEED_VAR_INC  increase the airspeed var value        Default  Default 
ACTION_AP_AIRSPEED_VAR_SET  set the airspeed var value  const float      Speed  Meter Per Second 
ACTION_AP_ALT_HOLD_OFF  activate off altitude mode        Default  Default 
ACTION_AP_ALT_HOLD_ON  activate on altitude mode        Default  Default 
ACTION_AP_ALT_HOLD_TOGGLE  toggle altitude mode        Default  Default 
ACTION_AP_ALT_VAR_SET  ALtitude Autopilot panel var set [ft]  const float      Length  Feet 
ACTION_AP_ALT_VAR_SET_METRIC  set the altitude var mateic value  const float      Length  Meter 
ACTION_AP_APR_HOLD_ON  activate on panel approach mode        Default  Default 
ACTION_AP_ATTITUDE_HOLD_OFF  activate off nav1 mode        Default  Default 
ACTION_AP_ATTITUDE_HOLD_ON  activate on panel attribute mode        Default  Default 
ACTION_AP_ATTITUDE_HOLD_TOGGLE  toggle attribute mode        Default  Default 
ACTION_AP_FPA_HOLD_OFF  Hold FPA Off        Default  Default 
ACTION_AP_FPA_HOLD_ON  Hold FPA On        Default  Default 
ACTION_AP_FPA_VAR_SET  set vs var english  const float      Default  Default 
ACTION_AP_HEADING_HOLD_OFF  activate off heading mode        Default  Default 
ACTION_AP_HEADING_HOLD_ON  activate on heading mode        Default  Default 
ACTION_AP_HEADING_VAR_DEC  decrease the heading bug value        Default  Default 
ACTION_AP_HEADING_VAR_INC  increase the heading bug value        Default  Default 
ACTION_AP_HEADING_VAR_SET  set the heading bug value  const float      Angle  Degree 
ACTION_AP_LNAV_HOLD_OFF  toggle Lnav mode        Default  Default 
ACTION_AP_LNAV_HOLD_ON  toggle Lnav mode        Default  Default 
ACTION_AP_LNAV_HOLD_TOGGLE  toggle Lnav mode        Default  Default 
ACTION_AP_MACH_HOLD_TOGGLE  toggle mach mode        Default  Default 
ACTION_AP_MACH_VAR_DEC  decrease the mach value        Default  Default 
ACTION_AP_MACH_VAR_INC  increase the mach var value        Default  Default 
ACTION_AP_MACH_VAR_SET  set mach  const float      Default  Default 
ACTION_AP_MASTER_OFF  activate on the autopailot        Default  Default 
ACTION_AP_MASTER_ON  activate on the autopailot        Default  Default 
ACTION_AP_MASTER_TOGGLE  activate on the autopailot        Default  Default 
ACTION_AP_PITCH_HOLD_OFF  Hold Pitch Off        Default  Default 
ACTION_AP_PITCH_HOLD_ON  Hold Pitch On        Default  Default 
ACTION_AP_PITCH_RATE_HOLD_OFF  Hold Pitch Off        Default  Default 
ACTION_AP_PITCH_RATE_HOLD_ON  Hold Pitch On        Default  Default 
ACTION_AP_PITCH_RATE_VAR_SET  set vs var english  const float      Angle  Degree 
ACTION_AP_PITCH_VAR_SET  set vs var english  const float      Angle  Degree 
ACTION_AP_ROLL_HOLD_OFF  Hold Roll Off        Default  Default 
ACTION_AP_ROLL_HOLD_ON  Hold Roll On        Default  Default 
ACTION_AP_ROLL_RATE_HOLD_OFF  Hold Roll Rate Off        Default  Default 
ACTION_AP_ROLL_RATE_HOLD_ON  Hold Roll Rate On        Default  Default 
ACTION_AP_ROLL_RATE_VAR_SET  set roll rate [DEG]  const float      Angle  Degree 
ACTION_AP_ROLL_VAR_SET  set vs var english  const float      Angle  Degree 
ACTION_AP_TRACK_HOLD_TOGGLE  toggle track mode        Default  Default 
ACTION_AP_TRACK_SELECT_OFF  activate off track selected mode        Default  Default 
ACTION_AP_TRACK_SELECT_ON  activate on track selected mode        Default  Default 
ACTION_AP_TRACK_VAR_DEC  decrease the track bug value        Default  Default 
ACTION_AP_TRACK_VAR_INC  increase the track bug value        Default  Default 
ACTION_AP_TRACK_VAR_SET  set the track bug value  const float      Default  Default 
ACTION_AP_VERTICAL_SPEED_HOLD  toggle vertical speed (VS) mode        Default  Default 
ACTION_AP_VERTICAL_SPEED_OFF  activate off vertical speed (VS) mode        Default  Default 
ACTION_AP_VERTICAL_SPEED_ON  activate on vertical speed (VS) mode        Default  Default 
ACTION_AP_VERTICAL_SPEED_VAR_DEC  decrease the vertical speed (VS) var value        Default  Default 
ACTION_AP_VERTICAL_SPEED_VAR_INC  increase the vertical speed (VS) var value        Default  Default 
ACTION_AP_VERTICAL_SPEED_VAR_SET  set vs var english  const float      Speed  Meter Per Second 
ACTION_AP_VNAV_HOLD_OFF  toggle Vnav mode        Default  Default 
ACTION_AP_VNAV_HOLD_ON  toggle Vnav mode        Default  Default 
ACTION_AP_VNAV_HOLD_TOGGLE  toggle Vnav mode        Default  Default 
ACTION_AP_WING_LEVELER  toggle wing leveler mode        Default  Default 
ACTION_AP_WING_LEVELER_OFF  activate off wing leveler mode        Default  Default 
ACTION_AP_WING_LEVELER_ON  activate on wing leveler mode        Default  Default 
ACTION_DAMAGE_AILERONS  damage the ailerons movement [0-1] (0-no damage, 1-max damage: stuck the ailerons)  const float      Default  Default 
ACTION_DAMAGE_AIR_BRAKES  damage the airbrakes movement [0-1] (0-no damage, 1-max damage: stuck the airbrakes)  const float      Default  Default 
ACTION_DAMAGE_ALL_AFTER_BURNERS  Demage all of the After Burners        Default  Default 
ACTION_DAMAGE_ALL_ENGINES_CUT_PERMANENT  Cut off all of the engines Permanently        Default  Default 
ACTION_DAMAGE_ALL_ENGINES_CUT_STARTABLE  Cut off all of the engines, allows restart        Default  Default 
ACTION_DAMAGE_ALL_ENGINESS_FIRE  Fire all of the engines        Default  Default 
ACTION_DAMAGE_ALL_LANDING_GEARS  damage all the landing gears movement [0-1] (0-no damage, 1-max damage: stuck all the landing gears)  const float      Default  Default 
ACTION_DAMAGE_ASIMETRIC_AILERONS  damage the movement of one of the ailerons [0-1] (0-no damage, 1-max damage: stuck the aileron)  const float      Default  Default 
ACTION_DAMAGE_ASIMETRIC_ELEVATORS  damage the movement of one of the elevators [0-1] (0-no damage, 1-max damage: stuck the elevator)  const float      Default  Default 
ACTION_DAMAGE_ASIMETRIC_FLAPS  damage the movement of one of the flaps [0-1] (0-no damage, 1-max damage: stuck the flap)  const float      Default  Default 
ACTION_DAMAGE_ASIMETRIC_RUDDERS  damage the movement of one of the rudders [0-1] (0-no damage, 1-max damage: stuck the rudder)  const float      Default  Default 
ACTION_DAMAGE_BAY_DOORS  damage the Bay Doors [0-1] (0-no damage, 1-max damage: stuck the bay doors)  const float      Default  Default 
ACTION_DAMAGE_ELEVATORS  damage the elevators movement [0-1] (0-no damage, 1-max damage: stuck the elevator)  const float      Default  Default 
ACTION_DAMAGE_FLAPS  damage the flaps movement [0-1] (0-no damage, 1-max damage: stuck the flaps)  const float      Default  Default 
ACTION_DAMAGE_FUEL_LEAK  Fuel Leak Damage        Default  Default 
ACTION_DAMAGE_FWD_LANDING_GEAR  damage the forward landing gear movement [0-1] (0-no damage, 1-max damage: stuck the fwd landing gear)  const float      Default  Default 
ACTION_DAMAGE_FWD_WHEEL_EXPLODE  damage the fwd wheel [0-1] (0-no damage, 1-max damage: Fwd Wheel fully explode)  const float      Default  Default 
ACTION_DAMAGE_LEFT_AFTER_BURNER  Demage the left After Burners        Default  Default 
ACTION_DAMAGE_LEFT_AILERON  damage the left aileron movement [0-1] (0-no damage, 1-max damage: stuck the left aileron)  const float      Default  Default 
ACTION_DAMAGE_LEFT_ELEVATOR  damage the left elevator movement [0-1] (0-no damage, 1-max damage: stuck the left elevator)  const float      Default  Default 
ACTION_DAMAGE_LEFT_ENGINES_CUT_PERMANENT  Cut off all of the left engines Permanently        Default  Default 
ACTION_DAMAGE_LEFT_ENGINES_CUT_STARTABLE  Cut off all of the left engines, allows restart        Default  Default 
ACTION_DAMAGE_LEFT_ENGINES_FIRE  Fire the left engines        Default  Default 
ACTION_DAMAGE_LEFT_FLAPS  damage the left rudder movement [0-1] (0-no damage, 1-max damage: stuck the left flap)  const float      Default  Default 
ACTION_DAMAGE_LEFT_LANDING_GEAR  damage the left landing gear movement [0-1] (0-no damage, 1-max damage: stuck the left landing gear)  const float      Default  Default 
ACTION_DAMAGE_LEFT_RUDDER  damage the left rudder movement [0-1] (0-no damage, 1-max damage: stuck the left rudder)  const float      Default  Default 
ACTION_DAMAGE_LEFT_WHEEL_EXPLODE  damage the left wheel [0-1] (0-no damage, 1-max damage: Left Wheel fully explode)  const float      Default  Default 
ACTION_DAMAGE_NO_CONTROL  Fuel Leak Damage        Default  Default 
ACTION_DAMAGE_NO_HYDRAULICS  Damage the hidraulic system        Default  Default 
ACTION_DAMAGE_RANDOM_ENGINE_CUT_PERMANENT  Randomly cut off one of the engines Permanently        Default  Default 
ACTION_DAMAGE_RANDOM_ENGINE_CUT_STARTABLE  Randomly cut off one of the engines, allows restart        Default  Default 
ACTION_DAMAGE_RANDOM_ENGINE_FIRE  Randomly Fire one of the engines        Default  Default 
ACTION_DAMAGE_RANDOM_LANDING_GEAR  damage a random landing gear movement [0-1] (0-no damage, 1-max damage: stuck the landing gear)  const float      Default  Default 
ACTION_DAMAGE_RANDOM_WHEEL_EXPLODE  damage a random wheel [0-1] (0-no damage, 1-max damage: Wheel fully explode)  const float      Default  Default 
ACTION_DAMAGE_REFUEL_BOOM  damage the refuel boom [0-1] (0-no damage, 1-max damage: stuck the refuel boom)  const float      Default  Default 
ACTION_DAMAGE_REFUEL_HATCH  damage the refuel hatch [0-1] (0-no damage, 1-max damage: stuck the refuel hatch)  const float      Default  Default 
ACTION_DAMAGE_RIGHT_AFTER_BURNER  Damage the right After Burner        Default  Default 
ACTION_DAMAGE_RIGHT_AILERON  damage the right aileron movement [0-1] (0-no damage, 1-max damage: stuck the right aileron)  const float      Default  Default 
ACTION_DAMAGE_RIGHT_ELEVATOR  damage the right elevator movement [0-1] (0-no damage, 1-max damage: stuck the right elevator)  const float      Default  Default 
ACTION_DAMAGE_RIGHT_ENGINES_CUT_PERMANENT  Cut off all of the right engines Permanently        Default  Default 
ACTION_DAMAGE_RIGHT_ENGINES_CUT_STARTABLE  Cut off all of the right engines, allows restart        Default  Default 
ACTION_DAMAGE_RIGHT_ENGINES_FIRE  Fire the right engines        Default  Default 
ACTION_DAMAGE_RIGHT_FLAPS  damage the right rudder movement [0-1] (0-no damage, 1-max damage: stuck the right flap)  const float      Default  Default 
ACTION_DAMAGE_RIGHT_LANDING_GEAR  damage the right landing gear movement [0-1] (0-no damage, 1-max damage: stuck the right landing gear)  const float      Default  Default 
ACTION_DAMAGE_RIGHT_RUDDER  damage the right rudder movement [0-1] (0-no damage, 1-max damage: stuck the right rudder)  const float      Default  Default 
ACTION_DAMAGE_RIGHT_WHEEL_EXPLODE  damage the right wheel [0-1] (0-no damage, 1-max damage: Right Wheel fully explode)  const float      Default  Default 
ACTION_DAMAGE_RUDDER  damage the rudders movement [0-1] (0-no damage, 1-max damage: stuck the rudders)  const float      Default  Default 
ACTION_DAMAGE_WHEEL_BRAKES  damage the wheelBrakes movement [0-1] (0-no damage, 1-max damage: stuck the wheelBrakes)  const float      Default  Default 
ACTION_DEACTIVATE_TRIMMER  deactive the Trimmer        Default  Default 
ACTION_DEC_BANK_LIMITER_STAGE  decrease bank limiter stage        Default  Default 
ACTION_EXTRACT_FLAPS  send horizontal joystick command        Default  Default 
ACTION_EXTRACT_HATCH_DOORS  extract Hatch Doors        Default  Default 
ACTION_EXTRACT_LANDING_GEARS  extract Landing Gears        Default  Default 
ACTION_EXTRACT_LANDING_HOOK  extract Landing Hook        Default  Default 
ACTION_EXTRACT_LEFT_WHEEL_BRAKE  send horizontal joystick command        Default  Default 
ACTION_EXTRACT_PARKING_BRAKES  send horizontal joystick command        Default  Default 
ACTION_EXTRACT_REFULING_BOOM  extract Refuling Boom        Default  Default 
ACTION_EXTRACT_RIGHT_WHEEL_BRAKE  send horizontal joystick command        Default  Default 
ACTION_EXTRACT_SPEED_BRAKES  extract Speed Brakes        Default  Default 
ACTION_INC_BANK_LIMITER_STAGE  increase bank limiter stage        Default  Default 
ACTION_INCREASE_LEFT_WHEEL_BRAKE  send horizontal joystick command  const float      Default  Default 
ACTION_INCREASE_RIGHT_WHEEL_BRAKE  send horizontal joystick command  const float      Default  Default 
ACTION_MODEL_MOTION_ENABLE  Enable/Disable the model motion, loaction updated externally  const bool      Default  Default 
ACTION_RELOAD_DATA  Reload Aircraft Atk file        Default  Default 
ACTION_RETRACT_FLAPS  send horizontal joystick command        Default  Default 
ACTION_RETRACT_HATCH_DOORS  retract Hatch Doors        Default  Default 
ACTION_RETRACT_LANDING_GEARS  retract Landing Gears        Default  Default 
ACTION_RETRACT_LEFT_WHEEL_BRAKE  send horizontal joystick command        Default  Default 
ACTION_RETRACT_PARKING_BRAKES  send horizontal joystick command        Default  Default 
ACTION_RETRACT_RIGHT_WHEEL_BRAKE  send horizontal joystick command        Default  Default 
ACTION_RETRACT_SPEED_BRAKES  retract Speed Brakes        Default  Default 
ACTION_SEND_JOYSTICK_FWD  send vertical joystick command  const float      Default  Default 
ACTION_SEND_JOYSTICK_RIGHT  send horizontal joystick command  const float      Default  Default 
ACTION_SEND_MAGNETOS_LEFT_STATUS  Sets all engines magnetos left status (false-off true-on)  const bool      Default  Default 
ACTION_SEND_MAGNETOS_RIGHT_STATUS  Sets all engines magnetos right status (false-off true-on)  const bool      Default  Default 
ACTION_SEND_PROP_MIXTURE_LEVER  sets all engines Propeller Mixture Lever (0-1)  const float      Default  Default 
ACTION_SEND_PROP_PITCH_LEVER  sets all engines Propeller Pitch Lever (0-1)  const float      Default  Default 
ACTION_SEND_RPM  send rpm command  const float      Angular Velocity  RPM 
ACTION_SEND_RUDDER_INPUT  send horizontal joystick command  const float      Default  Default 
ACTION_SEND_STARTER_STATUS  Sets all engines Starter status (false-off true-on)  const bool      Default  Default 
ACTION_SEND_THROTTLE  send throttle command  const float      Default  Default 
ACTION_SET_AILERON_TRIM_ANGLE_RAD  set Aileron Trim Angle [rad]  const float      Angle  Radian 
ACTION_SET_AUTO_COORDINATION_STATUS  set auto coordination system status (0 - not active, 1 - active)  const int      Default  Default 
ACTION_SET_BANK_LIMITER_ANGLE  set bank limiter angle(deg)  const float      Angle  Degree 
ACTION_SET_BANK_LIMITER_STATUS  set bank limit system status (0 - not active, 1 - active)  const int      Default  Default 
ACTION_SET_CAT1_CONTROL_GAINS  Set the control Gains to CAT1        Default  Default 
ACTION_SET_CAT3_CONTROL_GAINS  Set the control Gains to CAT3        Default  Default 
ACTION_SET_ELECTRICAL_POWER  Set eletrical power(magnetos right and left status) (false-off true-on)  const int  const bool    Default  Default 
ACTION_SET_ELEVATOR_TRIM_ANGLE_RAD  set Elevator Trim Angle [rad]  const float      Angle  Radian 
ACTION_SET_EXTENDED_FUEL  set Extended fuel [kg]  const float      Mass  KG 
ACTION_SET_EXTENDED_LOADOUT  set Extended Loadout [kg]  const float      Mass  KG 
ACTION_SET_FLAPS_STAGE1  Set Aircraft Flaps to stage1        Default  Default 
ACTION_SET_FLAPS_STAGE2  Set Aircraft Flaps to stage2        Default  Default 
ACTION_SET_FLAPS_STAGE3  Set Aircraft Flaps to stage3        Default  Default 
ACTION_SET_FLAPS_STAGE4  Set Aircraft Flaps to stage4        Default  Default 
ACTION_SET_FLAPS_STAGE5  Set Aircraft Flaps to stage5        Default  Default 
ACTION_SET_FUEL_WEIGHT  set Aircraft fuel weight [kg]  const float      Mass  KG 
ACTION_SET_IS_REFULING  sets true if the aircraft is in refuling mode  const bool      Default  Default 
ACTION_SET_JOYSTICK_SENSITIVITY  set joystick sensitivity  const float      Default  Default 
ACTION_SET_LANDING_LIGHT  Set landing lights status (On/Off)  const bool      Default  Default 
ACTION_SET_MAGNETOS_LEFT_STATUS  Set magnetos left status (false-off true-on)  const int  const bool    Default  Default 
ACTION_SET_MAGNETOS_RIGHT_STATUS  Set magnetos right status (false-off true-on)  const int  const bool    Default  Default 
ACTION_SET_ORIENTATION  sets the orientation for the isRefuelingMode  const AngularVec &      Default  Default 
ACTION_SET_PROP_MIXTURE_LEVER  set Propeller Mixture Lever (0-1)  const int  const float    Default  Default 
ACTION_SET_PROP_PITCH_LEVER  set Propeller Pitch Lever (0-1)  const int  const float    Default  Default 
ACTION_SET_RUDDER_TRIM_ANGLE_RAD  set Rudder Trim Angle [rad]  const float      Angle  Radian 
ACTION_SET_SAS_STATUS  set stability augmentation system status (0 - not active, 1 - active)  const int      Default  Default 
ACTION_SET_SIMPLIFIED  set the simplicity of the flight model(1 - simplified, 0 - not simplified)  const bool      Default  Default 
ACTION_SET_STARTER_STATUS  Set Starter status (false-off true-on)  const int  const bool    Default  Default 
ACTION_SET_TAXI_LIGHT  Set taxi lights status (On/Off)  const bool      Default  Default 
ACTION_SET_THROTTLE_LEVER  set Throttle Lever (0-1)  const int  const float    Default  Default 
ACTION_SET_TRIMMER_STATUS  set trimmer system status (0 - not active, 1 - auto trimmer active, 2 - manuel trimmer active)  const int      Default  Default 
ACTION_SET_VELOCITY  sets the velocities for the isRefuelingMode  const LinearVec &      Speed  Meter Per Second 
ACTION_START_FLIGHT_MOTION_MODEL  start model motion  const Location &  const LinearVec &    Default  Default 
ACTION_TOGGLE_FUEL_FLOW  toggle the engine fuel flow  const int      Default  Default 
ACTION_UNLIMITED_FUEL  sets the amount of fuel to unlimited  const bool      Default  Default 
ACTION_YAW_DAMPER_OFF  activate off yaw damper mode        Default  Default 
ACTION_YAW_DAMPER_ON  activate on yaw damper mode        Default  Default 
ACTION_YAW_DAMPER_STATUS  set yaw damp system status (0 - not active, 1 - active)  const int      Default  Default 
ACTION_YAW_DAMPER_TOGGLE  toggle yaw damper mode        Default  Default 
ACTIVATE_PARACUTE_BRAKE  Activate parachute brake  const int  const int    Default  Default 
AUTO_COORDINATION_TOGGLE  Auto Coordination Toggle  const int  const int    Default  Default 
BANK_LIMITER_TOGGLE  Bank Limiter toggle  const int  const int    Default  Default 
DECREASE_FLAPS_STAGE  decrease flaps stage  const int  const int    Default  Default 
ENGINES_START  Engines Start  const int  const int    Default  Default 
ENGINES_STOP  Engines Stop  const int  const int    Default  Default 
EXTRACT_FLAPS  Extract flaps  const int  const int    Default  Default 
EXTRACT_LANDING_GEARS  Extract landing gears  const int  const int    Default  Default 
EXTRACT_LEFT_WHEEL_BRAKE  Extract left wheel brake  const int  const int    Default  Default 
EXTRACT_RIGHT_WHEEL_BRAKE  Extract right wheel brake  const int  const int    Default  Default 
EXTRACT_SPEED_BRAKES  Extract speed brakes  const int  const int    Default  Default 
EXTRACT_WHEEL_BRAKES  Extract wheel brakes  const int  const int    Default  Default 
INCREASE_FLAPS_STAGE  increase flaps stage  const int  const int    Default  Default 
LANDING_LIGHTS_TOGGLE  Landing lights toggle  const int  const int    Default  Default 
LEFT_BRAKE_OFF|LEFT_BRAKE_ON  Left Brake on/off  const int  const int    Default  Default 
LEFT_MAGNETO_TOGGLE  Toggles the Left Magneto state (On/Off)  const int  const int    Default  Default 
MIXTURE_LEVER_DEC  Mixture - decrease  const int  const int    Default  Default 
MIXTURE_LEVER_DOWN  Mixture full down  const int  const int    Default  Default 
MIXTURE_LEVER_INC  Mixture - increase  const int  const int    Default  Default 
MIXTURE_LEVER_SET  Mixture lever set  const int  const int    Default  Default 
MIXTURE_LEVER_UP  Mixture full up  const int  const int    Default  Default 
PEDDAL_LEFT|PEDDAL_RIGHT  Pedal left/right  const int  const int    Default  Default 
PROPELLER_LEVER_DEC  Propeller - decrease  const int  const int    Default  Default 
PROPELLER_LEVER_DOWN  Propeller full down ( Feathering)  const int  const int    Default  Default 
PROPELLER_LEVER_INC  Propeller - increase  const int  const int    Default  Default 
PROPELLER_LEVER_SET  Propeller lever set  const int  const int    Default  Default 
PROPELLER_LEVER_UP  Propeller full up  const int  const int    Default  Default 
RELOAD_ATK_DATA  Reloads the current atk file data  const int  const int    Default  Default 
RETRACT_FLAPS  Retract flaps  const int  const int    Default  Default 
RETRACT_LANDING_GEARS  Retract landing gears  const int  const int    Default  Default 
RETRACT_LEFT_WHEEL_BRAKE  Retract left wheel brake  const int  const int    Default  Default 
RETRACT_RIGHT_WHEEL_BRAKE  Retract right wheel brake  const int  const int    Default  Default 
RETRACT_SPEED_BRAKES  Retract speed brakes  const int  const int    Default  Default 
RETRACT_WHEEL_BRAKES  Retract wheel brakes  const int  const int    Default  Default 
RIGHT_BRAKE_OFF|RIGHT_BRAKE_ON  Right Brake on/off  const int  const int    Default  Default 
RIGHT_MAGNETO_TOGGLE  Toggles the Left Magneto state (On/Off)  const int  const int    Default  Default 
ROLL_TRIM_LEFT  each press add to the trim  const int  const int    Default  Default 
ROLL_TRIM_RIGHT  each press add to the trim  const int  const int    Default  Default 
SAS_TOGGLE  Sas toggle  const int  const int    Default  Default 
STARTER_PRESSED  Starter is being pressed  const int  const int    Default  Default 
STARTER_RELEASED  Starter was released  const int  const int    Default  Default 
STICK_DOWN|STICK_UP  Stick up/down  const int  const int    Default  Default 
STICK_LEFT|STICK_RIGHT  Stick left/right  const int  const int    Default  Default 
THROTTLE_LEVER_DEC  Throttle - decrease  const int  const int    Default  Default 
THROTTLE_LEVER_DOWN  Throttle - idle  const int  const int    Default  Default 
THROTTLE_LEVER_INC  Throttle - increase  const int  const int    Default  Default 
THROTTLE_LEVER_SET  Throttle lever set  const int  const int    Default  Default 
THROTTLE_LEVER_UP  Throttle - after burner  const int  const int    Default  Default 
TOGGLE_CONTROL_GAINS  Toggle between CAT1 & CAT3 Control Gains  const int  const int    Default  Default 
TOGGLE_FLAPS  Toggle flaps  const int  const int    Default  Default 
TOGGLE_LANDING_GEARS  Toggle landing gears  const int  const int    Default  Default 
TOGGLE_LEFT_WHEEL_BRAKE  Toggle left wheel brake  const int  const int    Default  Default 
TOGGLE_PARKING_BRAKES  Toggle parking brakes  const int  const int    Default  Default 
TOGGLE_RIGHT_WHEEL_BRAKE  Toggle right wheel brake  const int  const int    Default  Default 
TOGGLE_SPEED_BRAKES  Toggle speed brakes  const int  const int    Default  Default 
TOGGLE_WHEEL_BRAKES  Toggle wheel brakes  const int  const int    Default  Default 
TURN_PARKING_BRAKES_OFF  Turn parking brakes  const int  const int    Default  Default 
TURN_PARKING_BRAKES_ON  Turn parking brakes  const int  const int    Default  Default 
YAW_DAMPER_TOGGLE  Yaw Damper toggle  const int  const int    Default  Default 

back to top

Icon attributes.png Required Attributes

Name
ATT_CLOSEST_TOWER_CONTROL 
ATT_CURRENT_MANEUVER_WAY_POINT 
ATT_FORMATION_IS_LEADER 
ATT_FORMATION_TYPE 
ATT_MANUEVER_ACTIVE_MANUEVER_NAME 
ATT_MANUEVER_ACTIVE_MANUEVER_STACK 
ATT_MAX_HIT_SIGNATURE 
ATT_SMS_NUMBER_OF_WEAPONS_ON_REQUESTED_STATION 
ATT_TC_RUNWAY_TRACK 
ATT_TC_TAKEOFF_POSITION 
ATT_WEAPON_IDS_ON_STATION 
ATT_WEAPON_KIND 

back to top

Icon actions.png Required Actions

Name
ACTION_DO_NAVIGATE 
ACTION_DO_TACTICAL_ECHELON_FORMATION 
ACTION_DO_TACTICAL_LINE_FORMATION 
ACTION_DO_TACTICAL_TRAIL_FORMATION 
ACTION_DO_TACTICAL_WEDGE_FORMATION 
ACTION_SOUNDLOGIC_PLAY_FLAPS_SOUND 
ACTION_SOUNDLOGIC_PLAY_GEARS_SOUND 

back to top